High quality OKOOO Oxygen Sensor 234-4154 O2 sensor 89465-39885 8946539885 chip perception lambda Sensor for FORD
SG1802
213-1408
60-10288 234-4127
SG1802
2131408
6010288 2344127
5C5Z9F472BA
6L7Z9F472BA
YL849F472AE
YL8Z9F472AA
AJ03-18-861C
AJ0318861D
| Type : |
Heating Type |
| Sensitivity : |
200mV/mm |
| ltem Weight: |
0.078KG |
| ltem Length: |
510MM |
| Package Dimensions: |
14.5*6.5*4.5 |
| chip material: |
Aluminium oxide |
| Exterior Material: |
430F |
| Waterproof rating: |
IP68 |
| Applicable liguid temperature: |
-40 to 1000 degrees |
| chip craft |
Imported LTCC process |
| Length of ceramic chip : |
53MM |
| Pressure tightness： |
5Mpa <0.02com/min |
| Metal protective cover： |
310s stainless steel |
FORD ESCAPE 2.0L L4 （2002-2004）Upstream
FORD ESCAPE 3.0L V6 （2002-2006）Upstream Left
MAZDA TRIBUTE 2.0L L4 （2002-2004）Upstream Left
MAZDA TRIBUTE 3.0L V6 （2002-2004）Upstream Left
JAGUAR S-TYPE 3.0L V6 2002 Upstream
JAGUAR S-TYPE 4.0L V8 2002 Upstream
MERCURY MARINER 3.0L V6 2005 2006 Upstream Left
Metal / Ceramic / Plastic
T/T, Western Union, PayPal, Moneygram
Airline / Sea / Land Transportation
Shanghai Guangzhou Ningbo
the United States, Europe, Southeast Asia, Russia and the Middle East etc..
oxygen sensors common fault
1. Oxygen sensor poisoning
Oxygen sensor poisoning is a common and difficult to prevent fault, especially for cars that often use leaded gasoline. Even a new oxygen sensor can only work for a few thousand kilometers. If it is only a slight lead poisoning, then use a box of unleaded gasoline to remove the lead on the surface of the oxygen sensor and restore it to normal operation. However, due to excessively high exhaust temperature, lead often invades its interior, hindering the diffusion of oxygen ions and making the oxygen sensor ineffective. At this time, it can only be replaced.
In addition, silicon poisoning of oxygen sensors is also common. Generally speaking, silicon dioxide generated by the combustion of silicon compounds contained in gasoline and lubricating oil, and silicone gas emitted by improper use of silicone rubber sealing gaskets will make oxygen sensors ineffective, so good quality fuel and lubricating oil should be used. When repairing, correctly select and install rubber gaskets, and do not apply solvents and anti-sticking agents other than those specified by the manufacturer to the sensor.
2. Carbon deposits
Due to poor engine combustion, carbon deposits are formed on the surface of the oxygen sensor, or oil or dust and other deposits enter the oxygen sensor, which will hinder or block the external air from entering the oxygen sensor, making the signal output by the oxygen sensor inaccurate, and the ECU cannot correct the air-fuel ratio in time. Carbon deposits are mainly manifested as increased fuel consumption and significantly increased emission concentration. At this time, if the deposits are removed, normal operation will be restored.
3. Oxygen sensor ceramic fracture
The ceramic of the oxygen sensor is hard and brittle. It may be broken and fail if it is hitten with a hard object or blown with a strong airflow. Therefore, when handling it be particularly careful and if you find a problem please replace it in time.
4. Heater resistor wire burns out
For heated oxygen sensors, if the heater resistor wire burns out, it is difficult for the sensor to reach the normal operating temperature and loses its function.
5. The internal circuit of the oxygen sensor is disconnected
6. Check the appearance color of the oxygen sensor
Remove the oxygen sensor from the exhaust pipe and check whether the vent hole on the sensor housing is blocked or whether the ceramic core is damaged. If it is damaged, the oxygen sensor should be replaced.
Our company is a national science and technology enterprise, passed IATF 16949:2006
certification
CE certification, has a number of inventions, utility models, patents and other honors, has been
focusing on
the development and production of auto parts and motorcycle parts.
